---
title: LPU Initial Setup and Portal Configuration
description: "## Licensing - The LPU will come from Polywell flashed with the golden image. - Connect an Ethernet cable to the LPU. - Add :6111 to the end of the IPV4. - Fill out the information as listed below: -…"
url: "https://qa.flashparking.com/docs/lpu-configuration-for-luxonis-devices/"
updated: "2023-05-30"
category: Vision LPR / FlashVision (Uncanny based)
---

# LPU Initial Setup and Portal Configuration

## Licensing

- The LPU will come from Polywell flashed with the golden image.
- Connect an Ethernet cable to the LPU.
- Add :6111 to the end of the IPV4.
- Fill out the information as listed below:
  - Full name: HunterDunbar
  - Organization: FlashParking
  - Email :  [Visionuncanny@gmail.com](mailto:Visionuncanny@gmail.com)
  - Product key: *Obtain from Uncanny*
- Go to the Uncanny portal - [Uncanny Surveillance](https://monitor.uncannysurveillance.com/devices).
  - If you do not have a login, please reach out to @Hunter Dunbar or @roberto.salas.
- Find your device in the Devices tab

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Device-List-1024x521.png)

Change the device profile from FP-Installation to FlashParking-LPR by clicking the gear icon next to Device Profile.

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2022-11-23-at-12.29.34-PM-1024x518.png)

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2022-11-23-at-12.30.54-PM.png)

- Click save. The controller will then reboot. After several minutes, refresh the page to see the updated device.

### Final LPU Steps

- The next steps will run two scripts.
  - The first script is used to run the multiple docker containers as a single service.
  - The second script changes the hostname, installs LogMeIn, enables device uptime monitoring, and enables the Watchdog service.
- Click on Connect > Open Terminal in Browser.
  - Username: user
  - Password: flash123
- Next type the following:

```
cd /uncanny
sudo docker-compose up -d
```

![](https://qa.flashparking.com/wp-content/uploads/2023/05/docker.png)

```
cd /tmp
wget https://www.dropbox.com/s/v735do6v77627l6/install.sh
sudo bash install.sh
```

The script will take you through the following list of questions:

- What would you like to name this device?
  - The name should be the same as the lane
- Would you like to enable the watchdog device?
  - Answer “n” for now
- Would you like to install LogMeIn?
  - “y”
- Would you like to enable device monitoring?
  - If yes, follow the directions here:????

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2023-01-11-at-11.57.29-AM-1.png)

LPU Configuration is now complete.

## Camera Configuration

- Ensure all cameras are on the same network as the LPU(s).
- Go to the camera page - [Uncanny Surveillance](https://monitor.uncannysurveillance.com/devices).
- Find the LPU you would like to configure.
- Navigate to the Neighbors tab.
- Search for the IP address of the camera you want to configure and select “Open”
  - If using the default camera, “Honeywell International HPS” should appear in the Vendor column.

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2022-11-29-at-2.39.11-PM-1024x515.png)

- Click Get URL. The default port is :80
- A URL will be generated. Copy and paste this URL into your browser.

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2022-11-29-at-2.55.58-PM.png)

- You will now be at the camera login screen. The login credentials are as follows:
  - username: admin
  - password: Flashparcs1!

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2022-11-29-at-2.57.53-PM-1024x512.png)

- The homescreen should show a live view of the camera feed.

### System Setup

- Click on Setup → System Setup
  - Under General Settings, set the following:
    - Camera Name: Should have the same name as in LogMeIn.
    - Time zone: This should match the timezone the camera will be installed in.
    - Check enable daylight savings time
    - Select Automatic
    - NTP server: time.google.com
    - Click SAVE in the lower right-hand corner.

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2022-11-29-at-3.02.19-PM-1024x515.png)

### General Settings

- Now click on Camera Setup → General Settings
  - Video title: The lane name
    - Do not use the full LogMeIn name as it takes up too much space.
  - Check Show timestamp and video title in video and snapshots
  - Timestamp and video title font-size: 25
  - Day/Night Settings
    - IR cut filter: Auto mode
  - Click SAVE in the lower right-hand corner.

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2022-11-29-at-3.06.31-PM-1024x517.png)

### Video Settings

- Camera setup → Video
  - Mode:
    - Select 4-Megapixel (16:9) (MAX 60fps Non-True WDR).

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2022-11-29-at-3.12.58-PM-1024x516.png)

- Stream → Video settings for main stream:
  - Select H.264 (Default)
  - Frame size: 1280x720
  - Maximum frame rate: 12 fps
  - Bit rate control: Fixed quality
  - Quality = Excellent
  - Click SAVE in the lower right-hand corner.
- This must be repeated for each camera connected to the LPU.

![](https://qa.flashparking.com/wp-content/uploads/2023/05/Screenshot-2022-11-29-at-3.21.00-PM-1024x515.png)